Model predictive control for buck boost converter to improve BLDC motor stability
Abstract
Brushless Direct Current (BLDC) motors are widely employed in industrial automation and electric vehicles. However, mechanical load variations can cause output voltage fluctuations, increased ripple, and reduced stability of the DC–DC converter supplying the motor. This study proposes Model Predictive Control (MPC) for a Buck–Boost converter to improve voltage regulation and the dynamic performance of a BLDC motor drive. The system was modeled in MATLAB/Simulink and evaluated under resistive loads of 150–650 Ω, with and without the controller, and under mechanical load torques of 10–50 N·m. Without the controller, the output voltage varied between 305 V and 327 V with a voltage ripple of 3.41–9.72%. With MPC, the output voltage remained within 314–315 V for all resistive loads, the voltage ripple decreased to 0.044–0.178%, and the inductor current ripple was below 0.12%; however, a steady-state error of 4.67–5.00% relative to the 300 V reference remained. In the BLDC motor drive, the stator current increased from 5.961 A to 31.32 A and the electromagnetic torque from 11.7 N·m to 53.37 N·m as the load increased, while the rotor speed decreased from 1821 rpm to 577 rpm. The controller achieved rise times of 0.011–0.030 s and settling times of 0.030–0.080 s, whereas the output voltage varied from 356 V at light load to 307 V at full load. The proposed MPC substantially reduces voltage and current ripple and provides a fast, stable transient response, but further tuning is needed to remove the steady-state offset and improve voltage regulation at light loads.
Keywords
Full Text:
PDFReferences
A. Fergiansyah B., “Peningkatan kinerja buck boost converter menggunakan soft switching dengan metode close loop control system,” Undergraduate thesis, Fak. Tek., Univ. Lampung, Bandar Lampung, Indonesia, 2022.
Z. Alam, T. K. Roy, S. K. Ghosh, and M. A. Mahmud, “A hybrid non‐linear voltage controller design for DC–DC buck converters,” J. Eng., vol. 2023, no. 10, pp. 1–13, 2023, doi: 10.1049/tje2.12318.
R. A. Susilo, M. Johanuddin, and B. I. Sari, “Buck-boost converter using control proportional integral derivative (PID),” Int. J. Curr. Sci. Res. Rev., vol. 7, no. 1, pp. 659–665, 2024, doi: 10.47191/ijcsrr/V7-i1-62.
T. W. O. Stemi Salaus Moa, Afner S. Sinaha, Oktavianus Kati, Yosef Lefaan. Ekawati M. Ohee, “Application of Buck-Boost Converter with Soft Starter for Controlling DC Motor Speed based on Simulink Matlab,” pp. 37–43.
S. Danyali et al., “A New Model Predictive Control Method for Buck-Boost Inverter-Based Photovoltaic Systems,” Sustain., vol. 14, no. 18, 2022, doi: 10.3390/su141811731.
D. Mohanraj et al., “A Review of BLDC Motor: State of Art, Advanced Control Techniques, and Applications,” IEEE Access, vol. 10, pp. 54833–54869, 2022, doi: 10.1109/ACCESS.2022.3175011.
A. B. Rehiara and Y. Rumengan, “Performa kontroler MPC berbasis fungsi Laguerre dan kontroler PID untuk kendali konverter buck-boost,” in Pros. Semin. Nas. Rekayasa Teknologi Industri dan Informasi (ReTII), 2020, pp. 63–69. [Online]. Available: http://repository.unipa.ac.id/xmlui/handle/123456789/670
M. Ma’sum, R. Firmansyah, P. D. Widayaka, and S. A. Alamsyah, “Analisis respon dinamis buck-boost converter terhadap duty cycle dan beban,” J. Tek. Elektro, vol. 15, no. 1, pp. 30–37, 2026.
M. H. Arrosyid, B. Rahmat, and H. E. Wahanani, “Model predictive control (MPC) pada sistem kendali suhu ITCLAB dan pemantauannya menggunakan Internet of Things (IoT),” JUSIFOR: J. Sist. Inf. dan Inform., vol. 3, no. 1, pp. 1–9, 2024, doi: 10.33379/jusifor.v3i1.3882.
L. Persson, A. Hansson, and B. Wahlberg, “An optimization algorithm based on forward recursion with applications to variable horizon MPC,” Eur. J. Control, vol. 75, p. 100900, 2024, doi: 10.1016/j.ejcon.2023.100900.
D. Stenger, R. Ritschel, F. Krabbes, R. Voßwinkel, and H. Richter, “What Is the Best Way to Optimally Parameterize the MPC Cost Function for Vehicle Guidance?,” Mathematics, vol. 11, no. 2, pp. 1–19, 2023, doi: 10.3390/math11020465.
Z. Amalia, A. Khabib, E. Yudaningtyas, T. Machfuroh, F. A. Nadhifatul Aini, and S. D. Nasiqiati Rosady, “Field Oriented Control untuk Pengaturan Kecepatan Motor BLDC pada Sepeda Motor Listrik,” J. Elektron. dan Otomasi Ind., vol. 10, no. 1, pp. 1–8, 2023, doi: 10.33795/elkolind.v10i1.1977.
P. Astuti and H. Masdi, “Sistem kendali kecepatan motor BLDC menggunakan PWM berbasis mikrokontroler Arduino Uno,” JTEIN: J. Tek. Elektro Indones., vol. 3, no. 1, pp. 120–135, 2022.
B. Ullah, H. Ullah, and S. Khalid, “Direct model predictive control of noninverting buck-boost DC-DC converter,” CES Trans. Electr. Mach. Syst., vol. 6, no. 3, pp. 332–339, Sep. 2022, doi: 10.30941/CESTEMS.2022.00043.
X. Li, Y. Liu, and Y. Xue, “Four-switch buck-boost converter based on model predictive control with smooth mode transition capability,” IEEE Trans. Ind. Electron., vol. 68, no. 10, pp. 9058–9069, Oct. 2021, doi: 10.1109/TIE.2020.3028809.
DOI: https://doi.org/10.52626/joge.v5i2.101
Refbacks
- There are currently no refbacks.
St. Teknik II, Reumpet, Krueng Barona Jaya sub-district (23370), Aceh Besar District, Aceh Province, Indonesia.
http://geutheeinstitute.com/
1.png)




